Products tagged with Bicycle Bike tools
Tool kit set for servicing the bearings on 20 mm front axle 350 and 370 hubs.
Tooling for removing and installing the end cap retention rings as used on 15 mm front axle 350 and 370 hubs. Includes drift and guide to ensure perfect alignment when working on these hubs.
A special tool for holding 0.6 - 0.8 mm bladed spokes whilst wheel building or truing. Holds bladed spoke securely and allows nipples to be tensioned. Designed to be used in conjunction with TLDT108 nipple wrench.
Precision crafted in Switzerland to work perfectly with DT's stunning proline truing stand, these gauges are accurate to within 0.01 mm and can show up to 10 mm of run out.
An invaluable tool for getting the correct spoke tension during wheel building. Makes sure that spoke tension is tight and even, which is the key to successful wheel building. Fits all shapes of spokes. Accurate digital readout.
Tool kit set for servicing the bearings on straight pull 240 hubs, includes all the drifts and guides you need to install and remove the bearings easily and safely.
Tool kit set for servicing the bearings on radial 240 and 190 front hubs.
Tool kit set for servicing the bearings on 240 front hubs with 15mm front axles.
Genuine Wheels Manufacturing spare or a great tool on it's own To remove sealed bearings you will need the correct size extractor, 8mm & 10mm wrenches (for small sized extractors) or 13mm and 17mm wrenches (for large sized extractors).
Genuine Wheels Manufacturing spare or a great tool on it's own To remove sealed bearings you will need the correct size extractor, 8mm & 10mm wrenches (for small sized extractors) or 13mm and 17mm wrenches (for large sized extractors), hammer and punch.
Receiver cup sleeve for Wheels Mfg sealed bearing extractors Machined aluminium sleeve, anodized red with 39mm ID and 52mm OD 1/2 thru hole to fit over our 1/2 threaded rod press handles.
Receiver cup sleeve for Wheels Mfg sealed bearing extractors Machined aluminium sleeve, anodized red with 42mm ID and 52mm OD 1/2 thru hole to fit over our 1/2 threaded rod press handles.
Receiver cup sleeve for Wheels Mfg sealed bearing extractors Machined aluminium sleeve, anodized red with 44mm ID and 52mm OD. 1/2 thru hole to fit over our 1/2 threaded rod press handles.
Genuine Wheels Manufacturing Spare Designed for use with the Wheels Manufacturing Large Bearing Press.
Precision machined anodized aluminium tool designed to allow for easy installation, removal or adjustments of the Shimano Hollowtech II Crankset compression bolt.
E-bike socket designed for installing and removing compatible cassettes on Bafang hub-drive motors without removing motor wiring Centre clearance for E-Bike wiring is 0.812, with a 12-spline 23mm OD tool fitting.
AXLE RULER - PRO . Axle Ruler Pro Feast your eyes on the Axle Ruler Pro - the precision tool that's about to revolutionize your bike mechanic game.
The Bottom Bracket Gauge Tool was designed to provide all the necessary measurements to identify the proper bottom bracket for a specific bike configuration The gauge can measure everythig.
Complete tool kit for installing Wheels Manufacturing bottom brackets Kit includes our new bottom bracket socket tool for installing our bottom bracket cups, along with new sealed bearing drifts for 22mm, 24mm, 29mm and 30mm ID bearings.
A Thin Flange Bottom Bracket Socket designed to create a tight grip on thin flange bottom bracket to avoid slipping while torquing cups into bike frames This single-sided socket is used for installing and removing 48.
A Thin Flange Bottom Bracket Socket designed to create a tight grip on thin flange bottom bracket to avoid slipping while torquing cups into bike frames This single-sided socket is used for installing and removing Praxis T47 bottom brackets.
Bearing extractors set for pushing out 22mm, 24mm, 29, and 30mm ID sealed bearings from bottom bracket cups Compatible with the 1/2 threaded press rod and handles such as WMTL7 and WMTL7PRO.
This drift and over axle set is used to install common-sized thru-axle hub and frame sealed bearings Compatible with the 3/8 Wheels Mfg kits such as WMTLBBPPK, WMTLBBPEK and WMTL4083.
