Products tagged with Bicycle Bike tools
Tapping instructions . Remove your old star-nut and tap the top of your steerer tube. This might sound daunting, but we've made it super easy to do on your bike, without even removing your fork.
Easy to install. Easy to carry. And compatible with pretty much any bike with a steerer tube. The included 9 function Multi Tool contains your most used tools and lives inside your stem/steerer tube.
Professional tool kit for servicing all Ratchet EXP, Hügi ratchet and 3-Pawl DT Swiss Hubs.
Bearing installation tool for non-drive side bearings on rear Mon Chasseral wheels. Please consult your wheel's service manual before ordering this tool to see whether it is required.
A dedicated press and drift for the safe removal and installation of the driveside rear hub bearing from Ratchet EXP system rear hubs.
Tool for removing the threaded cap on certain DiCUT wheels. Please consult your wheel's service manual before ordering this tool to see whether it is required.
35 mm bearing installation and removal cylinder. Please consult your wheel's service manual before ordering this tool to see whether it is required.
TL-PD400 cone adjusting tool set is product number 6 in the attached image. Genuine Shimano replacement part.
TL-FH17A seal ring presser is product number 28 in the attached image. Genuine Shimano replacement part.
TL-FC430 chainring installation tool for chainring for DU-EP801 / DU-EP600 is product number 7 in the attached image. Genuine Shimano replacement part.
An invaluable tool for getting the correct spoke tension during wheel building. Makes sure that spoke tension is tight and even, which is the key to successful wheel building. Fits all shapes of spokes. Accurate dial gauge readout.
Tool kit set for servicing the bearings on straight pull 240 hubs, includes all the drifts and guides you need to install and remove the bearings easily and safely.
Tool kit set for servicing the bearings on radial 240 and 190 front hubs.
Headset cup drifts for use with the Wheels Mfg Headset Cup Press 1/2 thru hole Drift is machined with steps to fit common headset cups with 1-1/8 and 1-1/2 bearings May work with other size cups Not recommended for use with Wheels Mfg.
Headtube drifts for use with the Wheels Mfg Headset Cup Press 1/2 thru hole Drift is machined with multiple steps to fit common head tube inner diameters listed below Not recommended for use with Wheels Mfg PRESS-1 or PRESS-4 handles.
Receiver cup sleeve for Wheels Mfg sealed bearing extractors Machined aluminium sleeve, anodized red with 44mm ID and 52mm OD. 1/2 thru hole to fit over our 1/2 threaded rod press handles.
Genuine Wheels Manufacturing Spare Designed for use with the Wheels Manufacturing Large Bearing Press.
Genuine Wheels Manufacturing Spare Designed for use with the Wheels Manufacturing Large Bearing Press.
Precision machined anodized aluminium tool designed to allow for easy installation, removal or adjustments of the Shimano Hollowtech II Crankset compression bolt.
Precision machined anodized aluminium tool designed to allow for easy adjustment of the Fox DHX2 and FLOAT X2 shocks requiring a 3mm and 6mm hex wrench This small pocket sized tool allows for easy trail side adjustments of rebound and compression.
AXLE RULER - Plug Gauge . Tech Specs: Material: 6061 aluminum Hard anodized Avilable in Male and Female measurements: M9x1, M9x26, 3/8x24, 3/8x26, M10x1, M10x26, M12x1, M12x1.25, M12x1.5, M12x1.75, M14x1.5, M15x1, M15x1.
AXLE RULER - Plug Gauge . Tech Specs: Material: 6061 aluminum Hard anodized Avilable in Male and Female measurements: M9x1, M9x26, 3/8x24, 3/8x26, M10x1, M10x26, M12x1, M12x1.25, M12x1.5, M12x1.75, M14x1.5, M15x1, M15x1.
AXLE RULER - Plug Gauge . Tech Specs: Material: 6061 aluminum Hard anodized Avilable in Male and Female measurements: M9x1, M9x26, 3/8x24, 3/8x26, M10x1, M10x26, M12x1, M12x1.25, M12x1.5, M12x1.75, M14x1.5, M15x1, M15x1.
