Bike tools
Ring Nut tool required for removing and replacing inner bearings on pawl drive rear hubs. which are located behind the internal ring nutOnly works on Pawl hubs as used on DT complete wheels. for ratchet and aftermarket hubs please use tool HBDT835
Replacement pin for Unior 1647 screw-type chain tool. Durable and precise, perfect for maintaining chain tool performance.
TL-S703 Drain Pot and Syringe Kit is product number 49 in the attached image. Genuine Shimano replacement part.
TL-S702 right hand cone installation tool is product number 46 in the attached image. Genuine Shimano replacement part.
Tough genuine Shimano tools. Hardened steel for longevity and durability.
TL-CN10 Quick link tool is product number 1 in the attached image. Genuine Shimano replacement part.
Removes locking collar from Shimano SPD pedals. Plastic construction ensures that you cannot damage or over-tighten spindle locknut.
Tough genuine Shimano tools. Hardened steel for longevity and durability.
The Threadless Carrier is the easiest way to carry the 20-function EDC Tool in your stem. Just remove the star nut, drop it into your steerer tube and secure from below. Pop your EDC Tool into the carrier and hit the trail. Never forget your tools again.
The EDC Tube Strap Mount is a flat mounting bracket with an included EDC Gear Tension Strap. It lets you carry a spare tube without scratching or scuffing your frame. The strap's adjustable 355mm length lets you carry other stuff too, and it's replaceable
Replacement bacon strips for your EDC tire plug jabber tool. Strips stash easily into the EDC storage capsule ready to fix flats in seconds. KIT INCLUDES. 15x Bacon Strips. PRODUCT SPECS . Material: Bacon. Compatible with: EDC PLUG KIT.
Tapping instructions . Remove your old star-nut and tap the top of your steerer tube. This might sound daunting, but we've made it super easy to do on your bike, without even removing your fork.
The EDC Plug & Plier Kit is the perfect addition to the EDC V2 Tool .
The EDC Plug Kit is the perfect addition to the EDC V2 Tool system. The Jabber Tool and bacon strips store perfectly within the small EDC capsule. What's in the Box . Tire Plug Jabber Tool. 15x Bacon Strips. Product Specs . Material: Aluminum/steel/bacon.
Tool kit set for servicing the bearings on DT Swiss Predictive Steering front hubs, includes 37 and 27 x 30 mm installation cylinders and a disassembly tool for 18 mm diameter axles.
Bearing installation tool for non-drive side bearings on rear Mon Chasseral wheels. Please consult your wheel's service manual before ordering this tool to see whether it is required.
Tooling for removing and installing the end cap retention rings as used on 15 mm front axle 350 and 370 hubs. Includes drift and guide to ensure perfect alignment when working on these hubs.
Tool for removing the threaded cap on certain DiCUT wheels. Please consult your wheel's service manual before ordering this tool to see whether it is required.
Workshop tool kit for replacing the ratchets and bearings in most Ratchet EXP 240 and 180 rear hubs.
An invaluable tool for getting the correct spoke tension during wheel building. Makes sure that spoke tension is tight and even, which is the key to successful wheel building. Fits all shapes of spokes. Accurate dial gauge readout.
Tool kit set for servicing the bearings on radial 240 and 190 front hubs.
Tool kit set for servicing the bearings on 240 front hubs with 15mm front axles.
Headset cup drifts for use with the Wheels Mfg Headset Cup Press 1/2 thru hole Drift is machined with steps to fit common headset cups with 1-1/8 and 1-1/2 bearings May work with other size cups Not recommended for use with Wheels Mfg.
Genuine Wheels Manufacturing Spare Designed for use with the Wheels Manufacturing Large Bearing Press.
