Bike tools
A simple adaptor to allow the use of a standard crank extractor tool with Shimano Octalink splined cranks.
This tool allows the removal of MAHLE bottom bracket bearings without disassembling them from the bike, significantly reducing the risk of damage and improving maintenance efficiency.
Tooling to remove the MAHLE BB.(Mandatory to use when removing the BB, otherwise the electronics might break).
The EDC Top Cap is the original, most widely-used and most cost-effective way to store an EDC Tool in your steerer tube. It's also the world's lightest headset top cap and the #1 choice for the world's fastest EWS racers.
Tapping instructions . Remove your old star-nut and tap the top of your steerer tube. This might sound daunting, but we've made it super easy to do on your bike, without even removing your fork.
FC-R9100-P magnet setting tool is product number 13 in the attached image. Genuine Shimano replacement part.
TL-PD400 cone adjusting tool set is product number 6 in the attached image. Genuine Shimano replacement part.
Ring Nut tool required for removing and reinstalling the ratchet DEG ring nut. Only works on Ratchet DEG systems. Simple to use, fits into a vice for workshop use.
An invaluable tool for getting the correct spoke tension during wheel building. Makes sure that spoke tension is tight and even, which is the key to successful wheel building. Fits all shapes of spokes. Accurate digital readout.
A tool to simplify the lacing of wheels, by holding the nipple. Simply clip the nipple onto the end of the tool and feed it through the rim. Perfect for deep section rims where access is limited.
Yeah you've got big, manly hands but some tyre and rim combinations can lead to a pretty snug fit, these levers should help get your fresh tread on to your hoops without bending your mum's finest silverware.
Genuine Wheels Manufacturing Spare Designed for use with the Wheels Manufacturing Large Bearing Press.
E-bike socket designed for installing and removing compatible cassettes on Bafang hub-drive motors without removing motor wiring Centre clearance for E-Bike wiring is 0.812, with a 12-spline 23mm OD tool fitting.
AXLE RULER - Plug Gauge . Tech Specs: Material: 6061 aluminum Hard anodized Avilable in Male and Female measurements: M9x1, M9x26, 3/8x24, 3/8x26, M10x1, M10x26, M12x1, M12x1.25, M12x1.5, M12x1.75, M14x1.5, M15x1, M15x1.
Designed to press in all current Wheels Mfg bottom brackets.
Gone are the days when shop mechanics grabbed whatever socket was close enough to the sealed bearing size and just tapped it in The Bearing Press Pro Kit replaces that archaic installation system, providing the right tool for the job.
A Thin Flange Bottom Bracket Socket designed to create a tight grip on thin flange bottom bracket to avoid slipping while torquing cups into bike frames This single-sided socket is used for installing and removing 48.
The GXP-LEFT open bore adapter is used to press 22x37 sealed bearings into SRAM GXP bottom bracket cups and direct fit frames like TREK BB90 The adapter is machined with one step at 22mm OD, which fits into the center of the sealed bearing.
These extractors remove sealed bearings with inside diameters from 8mm,9mm,10mm and12mm Removes these sealed bearing sizes: 608, 609, 6000, 6001 Bearing extractors grip the inside race of a sealed bearing, allowing the bearing to be tapped out of the hub.
The Headset Press Pro Install Kit is a robust, and easy to use tool The kit includes a machined aluminium handle, 1/2 threaded rod, two machined aluminium drifts and the Adjustable Press Stop allowing for easy drift placement.
Lezyne Pocket Torque Drive Black/Gold
Lezyne Classic Kit Tyre Patches (8 Patches)
The PRO Team Digital Torque Wrench ensures that you will never overtighten a nut or bolt again - featuring a ratchet system with a digital strain gauge and an LCD display It boasts a 1-20Nm torque range, can measure in ft-lb, in-lb and kg-cm.
